Flood Restoration Toronto is a referral service that connects Toronto and GTA property owners with independent flood restoration contractors. Flood restoration includes water extraction, moisture mapping, structural drying, cleaning, mould prevention and repairs. The emergency line, (647) 559-1203, is open 24 hours a day, 7 days a week.
Flood restoration is the work of returning a flooded property to its pre-loss condition. The work has six stages: assessment, water extraction, moisture mapping, structural drying, cleaning and repair. Each stage depends on the one before it. Drying cannot start until standing water is gone, and repairs cannot start until the structure is dry.
Flood Restoration Toronto is a referral website. When you call (647) 559-1203, the line connects you with an independent restoration contractor that serves your part of Toronto or the GTA. The contractor, not this website, performs and guarantees the work. This page explains each stage, what affects its duration and what to check before you hire.
Speed matters because water keeps moving after the flood stops. Drywall wicks water upward, subfloors soak it up and framing holds it. Mould can begin to grow on wet drywall and wood within 24 to 48 hours. Each hour of delay increases the amount of material that has to be removed and replaced.
Each service below is one stage of flood restoration. Each service page lists the equipment, typical duration and industry standard for that stage.
Flood damage restoration covers assessment, extraction, drying, cleaning and repair of a flooded property.
Water extraction removes standing water with submersible pumps and truck-mounted or portable extractors.
Flooded basement cleanup addresses stormwater, sump pump failure, plumbing leaks and foundation seepage below grade.
Sewage backup water is Category 3 water and requires protective equipment, containment, removal of porous materials and disinfection.
Structural drying typically takes 3 to 5 days and is verified with daily moisture readings.
Mould remediation uses containment, HEPA air filtration, removal of affected materials and a final check before re-occupancy.
What to expect when you call the emergency line.
Flood Restoration Toronto is a referral service. The emergency line connects you with an independent restoration contractor. The contractor performs the work.
The emergency line is open 24 hours a day, 7 days a week, including statutory holidays.
Partner contractors target arrival within 60 minutes in Toronto and the GTA. Distance, traffic and crew availability change the actual time.
Toronto, North York, Scarborough, Etobicoke, East York, Mississauga, Brampton, Vaughan, Markham, Richmond Hill, Pickering, Ajax and Oakville.
Detached homes, townhouses, condominium units, offices, retail units and industrial buildings.
IICRC S500 governs professional water damage restoration. IICRC S520 governs mould remediation.
Flood water travels beyond the visible wet area. Moisture meters and thermal imaging cameras locate moisture inside walls, subfloors and insulation.
Water wicks upward through drywall, spreads under flooring and soaks insulation and framing. Drywall, carpet pad and fibreglass insulation absorb water fastest. Concrete and hardwood release moisture slowest.
A floor that feels dry on the surface can still hold water in the subfloor beneath it. Technicians measure moisture content in each material instead of judging by touch. The flood damage restoration service covers the full sequence from assessment to repair.
Flood water contaminates furniture, carpets, appliances, cabinets and stored items. Non-porous items such as metal and glass can usually be cleaned and dried. Porous items such as upholstery, mattresses and particleboard cabinets are usually discarded after Category 2 or Category 3 exposure.
Separating damaged contents from dry contents limits cross-contamination. Photograph items before they are moved or discarded.
IICRC S500 sorts water into three categories by contamination level. The category sets the cleanup method.
Category 1 water comes from a sanitary source such as a broken supply line or a clean tub overflow. It can degrade to Category 2 if it sits on materials for 48 hours or more.
Category 2 water comes from dishwasher or washing machine discharge, sump pump overflow or a toilet overflow without faeces. It requires cleaning, disinfection and removal of most porous materials.
Category 3 water comes from sewage, sewer backup and rising river or creek water. It requires protective equipment, containment, removal of porous materials and disinfection before drying.
S500 also sorts water damage into four classes by how much water the materials hold. Class 1 is a small, low-moisture area. Class 2 is a whole room with wet carpet and moisture wicking up the walls. Class 3 is water from above that saturates ceilings, walls and insulation. Class 4 is deep saturation in dense materials such as hardwood, plaster and concrete, and it needs specialty drying. Read more on water damage cleanup in Toronto.
Six stages. Each stage has a defined output.
The emergency line records the address, water source and affected rooms, then connects a partner contractor.
The technician identifies the water category, affected area and moisture readings before work begins.
Pumps and extractors remove standing water. Residential extraction typically takes a few hours.
Dehumidifiers and air movers dry the structure. Drying typically takes 3 to 5 days.
The fifth stage is cleaning. The cleaning method follows the water category: detergent cleaning for Category 1, disinfection for Category 2 and removal plus disinfection for Category 3. The sixth stage is repair. Repair replaces the drywall, flooring, insulation and trim that were removed. Repair time depends on how much material came out, so a small clean-water loss may finish in days and a large sewage loss may take weeks.
Damage increases with every hour that water stays in contact with building materials.
Faster extraction reduces the volume of material that needs replacement.
Call (647) 559-1203 NowFour areas have their own pages. Other GTA cities are served from the same emergency line.
Etobicoke sits between the Humber River, Mimico Creek and Etobicoke Creek. Homes near these waterways face stormwater entry, and the Humber Bay Shores condominiums face unit-to-unit leaks. See flood restoration in Etobicoke.
North York contains the West Don River and Black Creek watersheds. Detached homes in Don Mills and Bayview Village face basement flooding, and Willowdale condominiums face leaks between units. See flood restoration in North York.
Scarborough has Highland Creek, the Rouge River and the Lake Ontario shoreline. Many homes were built from the 1950s to the 1970s with finished basements. See flood restoration in Scarborough.
Woodbridge is part of the City of Vaughan in York Region. Large detached homes with finished basements are common, and City of Toronto programs do not apply. See flood restoration in Woodbridge.
Each cause below leads to a different cleanup method. See the causes of flooding in Toronto guide.
Failed supply lines release clean (Category 1) water into walls, floors and ceilings.
Rainfall that exceeds drainage capacity enters basements through window wells, floor drains and foundation cracks.
Sewer backup water is Category 3 water. See sewage backup cleanup.
A failed pump leaves a basement open to groundwater and stormwater.
Foundation cracks and hydrostatic pressure let water enter below grade.
Water heaters, washing machines and dishwashers release Category 1 or Category 2 water.
Basement flooding is the most common residential flood loss in Toronto. A basement sits below grade, so water arrives from several directions: through floor drains, window wells, foundation cracks and the sump pit. Finished basements hold more material at risk, including drywall, carpet, insulation and built-in cabinets.
Basement cleanup starts with source control and water extraction. The technician then maps moisture in drywall, subfloor and framing, removes materials that cannot be saved and dries the structure. Concrete slabs release moisture slowly, so drying a basement often takes the full 3 to 5 days or longer.
Older Toronto neighbourhoods have combined sanitary and storm sewers. A surcharged sewer can push water up through a basement floor drain, and that water is Category 3. A backwater valve blocks this path, and the City of Toronto runs a Basement Flooding Protection Subsidy Program for installing one. Check the City of Toronto website for current eligibility. Details are on the flooded basement cleanup page.
Sewage backup water is Category 3 (grossly contaminated) water under IICRC S500. It can carry bacteria, viruses and parasites. Sewage cleanup therefore differs from clean-water extraction in four ways: technicians wear protective equipment, the work area is contained, porous materials are removed and surfaces are disinfected before drying begins.
Drywall, carpet, carpet pad, insulation and particleboard that touched sewage water are removed. Concrete, tile and sealed hard surfaces are cleaned and disinfected. Keep people and pets out of the affected area and do not use the affected drains. See sewage backup cleanup in Toronto.
Structural drying removes the moisture that remains after extraction. Technicians place LGR or desiccant dehumidifiers and axial or centrifugal air movers by room volume and wet-material area. They read moisture content in each material every day and compare it with a dry standard taken from unaffected materials in the same building.
Most residential jobs take 3 to 5 days. Indoor relative humidity between 30% and 50% limits mould growth, according to Health Canada guidance. See structural drying.
Mould needs moisture, organic material and time. Wet drywall paper, wood and insulation facing supply the food, and 24 to 48 hours of dampness supplies the time. Fast extraction and complete drying prevent most flood-related mould.
When mould has already grown, remediation uses containment barriers, HEPA air scrubbers, removal of affected porous materials and surface cleaning, then a check before the containment comes down. IICRC S520 is the reference standard. See mould remediation.
Toronto properties flood in every season, and each season has a typical cause.
Spring snowmelt combined with rain raises groundwater and loads sump pumps. Foundation seepage and sump pump failure are the typical spring causes.
Intense summer thunderstorms can drop more rain than storm sewers carry. Sewer backup and window well entry are the typical summer causes. The July 8, 2013 storm is a well-known Toronto example.
Fallen leaves block eavestroughs, downspouts and catch basins. Blocked drainage pushes water toward the foundation.
Pipes in unheated spaces freeze and crack in cold snaps. The water is released when the pipe thaws, often while the owner is away.
A flood plan helps in every season. Know where the main water shutoff is, test the sump pump before spring, keep downspouts directed away from the foundation and ask an insurer whether sewer backup coverage is on your policy.
Condominium flooding spreads between units. Water from a failed supply line or an overflowing appliance in an upper unit travels through ceilings, wall cavities and floors into the units below and into common areas. Restoration covers every affected unit, and each unit needs its own moisture readings. Tell property management immediately and notify your own insurer.
Commercial properties are restored in zones so that unaffected areas keep operating. Offices, retail units and industrial buildings need crew size and equipment count matched to floor area. Commercial losses also involve inventory, records and equipment, so documentation of damaged contents matters more than in a typical home.
A standard Ontario home insurance policy typically covers sudden and accidental water damage, such as a burst pipe or an appliance failure. Sewer backup and overland flood coverage are usually optional endorsements. Policy wording sets what is covered, so the insurer confirms coverage when the claim is opened.
Billing arrangements differ by contractor, so confirm whether the contractor bills the insurer directly or bills you before work begins.
Checks the property owner should make before signing. Verification is the owner's responsibility.
Confirm that the contractor holds a business licence for the municipality where the work happens.
Ask for a current certificate of insurance.
Ask for a WSIB clearance certificate for the workers on site.
Look for Water Damage Restoration Technician (WRT) and Applied Structural Drying (ASD) credentials.
Ask for a written scope of work and price before work begins.
Ask for daily moisture logs and equipment logs. Insurers request them.
Four first steps limit damage while professional help is on the way.
Shut off the water supply to a failed fixture or supply line only if the valve is reachable without entering standing water.
Stay out of standing water that touches outlets, cords, appliances or a panel. The Electrical Safety Authority advises calling a licensed electrician for a flooded panel.
Move belongings to dry areas only if the route is safe.
Photograph affected rooms, damaged items and the water line before cleanup begins. Insurers use these photos.
Answers about flood restoration in Toronto and the GTA.
Partner contractors target arrival within 60 minutes in Toronto and the GTA. Actual arrival time depends on distance, traffic and crew availability. The emergency line is open 24/7, including holidays.
A standard Ontario home policy typically covers sudden and accidental water damage such as a burst pipe. Sewer backup and overland flood coverage are usually optional endorsements. Coverage depends on the policy, so confirm with your insurer.
Residential water extraction typically takes a few hours. Structural drying typically takes 3 to 5 days. Repair time depends on how much drywall, flooring and insulation was removed.
Mould can begin to grow within 24 to 48 hours on wet drywall, wood and insulation. Drying below 50% indoor relative humidity limits growth.
Yes. Condominium units, offices, retail units and industrial buildings are covered. Crew size and equipment count scale with the affected floor area.
Flood Restoration Toronto is a referral service. Independent restoration contractors perform the work. Property owners should confirm each contractor's licence, insurance and IICRC certification before signing.
The emergency line serves Toronto, North York, Scarborough, Etobicoke, East York and the wider GTA, including Mississauga, Brampton, Vaughan, Markham, Richmond Hill, Pickering, Ajax and Oakville. Call and give your address to reach the nearest partner contractor.
Small volumes of Category 1 water can be removed with a wet-dry vacuum. Category 2 and Category 3 water should be handled by professionals with protective equipment. Moisture left in walls and floors needs professional drying even after the visible water is gone.
After drying, the contractor replaces removed drywall, flooring, insulation and trim and restores the finishes. Scope depends on how much material was removed, and a written scope of work sets the price.
Stop the water source if it is safe, stay out of water near electrical equipment, move valuables to dry areas and photograph the damage.
Eight common causes of flooding in Toronto. Read the guide.
What happens in the first hours. Read the emergency page.
Classes and categories of water damage. Read the guide.
How standing water is removed. Read the service page.
Call the 24/7 emergency line to reach a partner restoration contractor.
Call (647) 559-1203